-
loading
Solo con imagen

Header arduino


Listado top ventas header arduino

México (Todas las ciudades)
Header Para Arduino H/m Xl - 10 Pines. ------ EMPIEZA A EXPLORAR --------- 330ohms --------- TODOS NUESTROS PRECIOS INCLUYEN IVA Y SI FACTURAMOS PRODUCTO: Nombre: Header para Arduino H/M XL - 10 pines Marca: Sparkfun DESCRIPCIÓN: Conector hembra de 10 pines, con terminales extra largas ideales para apilar shields para Arduino. La separación entre los pines es de un décimo de pulgada (0.1"). Documentación Puedes descargar el datasheet en el siguiente link: Datasheet MÁS DETALLES: Peso del paquete: 0.0 kg Modelo: Header Condición: Nuevo GTIN: 731628414640 CPU: 731628414640 SKU: OS-01361 RECUERDA QUE SI ELABORAMOS FACTURAS Y TODOS NUESTROS PRECIOS YA INCLUYEN IVA ------EMPIEZA A EXPLORAR ------
$ 120
Ver producto
México (Todas las ciudades)
Módulo Interfaz Rs-485 Max485 Arduino. El Módulo Interfaz RS-485 permite agregar a tus desarrollos un puerto serial industrial RS-485. El estándar RS-485 es usado ampliamente en la industria como protocolo de capa física. Con este módulo puedes comunicarte con dispositivos que usan RS-485 con arduino o cualquier otro microcontrolador. Caracteristicas del Módulo Interfaz RS-485 MAX485 -Basado en el circuito MAX485 -Valido para sistemas de 5 volts -Conector tipo bornera para señales diferenciales de RS485 y tipo pin header -Operación Half-Duplex
$ 40
Ver producto
México (Todas las ciudades)
Modulo Ethernet Shield Enc28j60 Lan Red Spi Arduino Pic. Ranmex Caracteristicas: • Voltaje de alimentación: 3.3v • Comunicación: Interface SPI • Conexiones: header de 10 pines • Conector Rj45 HR911105A • LED indicador de alimentación • Cristal: 25MHz • Basado en el controlador Ethernet ENC28J60 de Microchip • Interfaz Ethernet 802.3 • Ancho de banda: 10 Mbps Half o Full Duplex (Manual) • Soportado por el Stack TCP/IP de Microchip Technology • Dimensiones: 51x33x17mm • Peso: 14 gramos
$ 1.012
Ver producto
México (Todas las ciudades)
Sensor De Corriente Dc Bidireccional Basado En El Ina219. Sensor de Corriente DC Bidireccional Basado en el controlador INA219 que te mide tanto corrie electrica como voltaje sobre bus serial I2C y puedes accesarlo con cualquier microcontrolador. Description: This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both the high side voltage and DC current draw over I2C with 1% precision. Most current-measuring devices such as our current panel meter are only good for low side measuring. That means that unless you want to get a battery involved, you have to stick the measurement resistor between the target ground and true ground. This can cause problems with circuits since electronics tend to not like it when the ground references change and move with varying current draw. This chip is much smarter - it can handle high side current measuring, up to +26VDC, even though it is powered with 3 or 5V. It will also report back that high side voltage, which is great for tracking battery life or solar panels. A precision amplifier measures the voltage across the 0.1 ohm, 1% sense resistor. Since the amplifier maximum input difference is ±320mV this means it can measure up to ±3.2 Amps. With the internal 12 bit ADC, the resolution at ±3.2A range is 0.8mA. With the internal gain set at the minimum of div8, the max current is ±400mA and the resolution is 0.1mA. Advanced hackers can remove the 0.1 ohm current sense resistor and replace it with their own to change the range (say a 0.01 ohm to measure up 32 Amps with a resolution of 8mA) We include a 6-pin header (so you can easily attach this sensor to a breadboard) as well as a 3.5mm terminal plug so you can easily attach and detach your load. Usage is simple. Power the sensor itself with 3 to 5VDC and connect the two I2C pins up to your microcontroller. Then connect your target power supply to VIN+ and the load to ground to VIN-. We have an Arduino library right now that will do all the gain, range and math for you - just plug and go! We'll have a more detailed tutorial up shortly. Specification: Uses the INA219B chip 0.1 ohm 1% 2W current sense resistor Up to +26V target voltage Up to ±3.2A current measurement, with ±0.8mA resolution This board/chip uses I2C 7-bit addresses 0x40, 0x41, 0x44, 0x45, selectable with jumpers Package Included: 1 X INA219 GY-219 Bi-direction DC Current Power Supply Breakout Sensor
$ 245
Ver producto

Anuncios Clasificados gratis - comprar y vender en México | CLASF - copyright ©2024 www.clasf.mx.